$499.95 USD

Description of Product HEXCAS006

Mustang II Tubular Control Arm Set by Helix™ includes 2 upper control arms and 2 lower control arms. Everything you need in one kit!



These control arms are a fully assembled, ready-to-install, direct replacement for stock upper and lower control arms on any Helix™ Mustang II IFS application and will fit most stock or aftermarket crossmembers with gussets installed. The lower arms are a direct replacement for stock Mustang II LCA’s with standard springs.



The Helix™ upper control arm assembly features 12 point TIG welded construction for maximum strength and durability, corrosion/rust resistant painted surface (except powder coated cross shaft), full .120 wall aircraft quality tubular design which is lighter weight yet much stronger than OE stock design and provides for more clearance for body sheet metal. Complete assembly includes cross shaft with rubber nitrile bushings & steel sleeves, knurled surface mount area* on cross shaft, screw-in ball joint with urethane dust boot and grease fitting, castle nut w/ cotter pin, castle nut spacer, 2 ea. Nyloc nuts and plain washers. These upper control arms are a stock width design (non-narrowed) and ready to drop in immediately out of the box. For all of your suspension needs, Helix™ delivers the winning edge for maximum performance when it really counts!



*Cross Shaft has knurled surface area on both sides of mounting points which provides “bite” into mounting surface area so as to prevent slippage and hold alignment settings. Surface area on cross shaft is unfinished and repainting/refinishing shaft is not recommended because any type of body filler or thick paint will prevent knurls from biting properly which can cause slippage and loss of alignment adjustment.



The Helix™ lower control arm assembly features precision fabricated TIG welded construction and 1 inch O.D. aircraft quality tubular steel design with full .120 wall for maximum strength and durability. This makes for a lighter weight yet much stronger LCA than the original stock arm that will endure a far higher stress load than the OEM design.



Complete left and right assembly includes 2 ea. 5/8-11 x 12” hex bolts (cross shaft), nylon locking nuts and large 5/8” washers, built-in rubber nitrile bushings w/ steel sleeves, screw-in ball joint with urethane dust boot & grease fitting, 7/16-14 x 7” hex bolt (Allen head), castle nut w/ cotter pin, and castle nut/ball joint spacers (2 ea. x 2). This lower control arm assembly is stock design and ready to drop in immediately out of the box. For all of your suspension needs, Helix™ deliver the winning edge for maximum performance when it really counts!



Stay ahead of the pack with Helix Suspension. For more information on Helix products please contact your local dealer, or go to http://www.helixsuspension.com.

Features

• Includes :: 2 Tubular Upper Control Arms & 2 Tubular Lower Control Arms
• Application :: Mustang II
• Type :: Tubular
• Feature :: All Steel Construction
• Tube Finish :: Plain Painted Surface
• Cross Shaft Finish :: Powder Coated
• Screw In Ball Joint :: Yes
• TIG Welded :: Yes
• Grease Fitting Included :: Yes
• Urethane Dust Boot :: Yes
• Fully Assembled :: Yes
• Adjustable :: No
• Hardware Included :: Yes
• Feature :: Full .120 Wall Tubing
• Upper Control Arm Tube O.D. :: 7/8" (22mm)
• Upper Control Arm Center to Center Length :: 8” (20.32 cm)
• Upper Control Arm Feature :: (Ball Joint Shaft Center to Cross Shaft Eye Center)
• Upper Control Arm Overall Width :: 10.5” (26.67 cm)
• Upper Control Arm Overall Length :: 9.5” (24.13 cm)
• Upper Control Arm Cross Shaft O.D. :: .78” (19.8 mm)
• Lower Control Arm Tube O.D. :: 1 in. (25 mm)
• Lower Control Arm Overall Width :: 10.5” (26.7 cm)
• Lower Control Arm Overall Length :: 14.75” (37.46 cm)
• Lower Control Arm Cross Shaft O.D. :: 5/8” (16 mm)